mercredi 30 septembre 2009

How do I move Exchange Server to a new server?

How do I move Exchange Server to a new server?

A Web Exclusive from FAQ for Windows
Paul Robichaux
Exchange/Outlook
InstantDoc #20294
FAQ for Windows Email this ArticlePrinter FriendlyReader CommentsDigg ThisDel.icio.usRSS
Subscribe to Windows IT Pro | See More Tips Articles Here | Reprints | Or get the Monthly Online Pass—only $5.95 a month!




A. There are two ways: the hard way and the Ed Crowley way. The hard way is to do a complete backup of the old server, then restore the backup to the new server. How hard this actually is depends on your configuration. Even if the backup and restore are easy to accomplish, you must remove the old server before setting up the new one (because you can’t have two servers with the same name at the same time), and that means you run an increased risk of downtime.

In contrast, the Ed Crowley Server Move Method requires you to set up your new server in parallel with the old one, cutting over to the new one only when you're sure it's working properly. To use the Ed Crowley Server Move Method, perform the following steps:

Bring up a new server as a new server in the same site. Use a different name for the new server. If you need to move Exchange to another server with the same name, follow the instructions in the Microsoft article “XADM: How to Move Exchange Server to a New Computer with the Same Name” (http://support.microsoft.com/support/kb/articles/q155/2/16.asp).
To move user mailboxes to the new server, start Microsoft Exchange Administrator, click Tools, and select Move Mailbox. You can move all the mailboxes at once, one at a time, or several at a time. In many cases, you can move mailboxes during working hours because each user is locked out of his or her mailbox only while that mailbox is being moved.
Create replicas of the public folders on the new server. When the contents of the folders have been replicated (do wait a little while!), remove the folders from the old server.
Create new connectors on the new servers. Change the costs of the old connectors you're replacing to be higher than the new ones, then recalculate routing.
Create mail exchanger (MX) records pointing to the new Internet Mail Service (IMS) as appropriate, and change the cost on the old MX record so that it’s higher than the costs on the new records. When you’ve verified that messages are flowing across the new connectors, remove the old ones, then recalculate routing again.
Follow the steps in the Microsoft article “XADM: How to Remove the First Exchange Server in a Site” (http://support.microsoft.com/support/kb/articles/q152/9/59.asp) if the server you're replacing is the first one in the site.
Leave the old server up for a while to give Messaging API (MAPI) clients time to connect to the new server automatically ( the old server provides referrals to the new one). It's true—you don't have to reconfigure MAPI clients!
Tell POP3 and IMAP4 users how to reconfigure their clients to point to the new server.
If you have a WINS or DNS alias for the old server, point it to the new server.
Stop the Exchange services on the old server, then use Exchange Administrator to delete the old server's server object, thus removing it from the site.
End of Article




Does this article apply to exchange 2000?

Patrick May 06, 2002


--------------------------------------------------------------------------------

Yes. It works with Exchange 2000. We just followed this article to successfully move from an old Gateway server to a new Compaq/HP server. It worked without a hitch and we're going to shut down the old server next week after we're pretty sure all of the Outlook clients have been referred to the new server.

Mark McClure July 24, 2002


--------------------------------------------------------------------------------

Does this method work if the current exchange server is the Domain controller?

Cody September 22, 2003


--------------------------------------------------------------------------------

Yes, although there is a little more involved because you are moving active directory also.

markerman April 20, 2005 (Article Rating: )


--------------------------------------------------------------------------------

We have an existing server running Exchange 2000 and are looking to upgrade to a new server and to Exchange 2003. We are also considering using our current Exchange 2000 server as a front end Exchange server if possible.

BAK2IT November 14, 2006 (Article Rating: )


--------------------------------------------------------------------------------

You can probably use your current servers, depending on their age and configuration. Your best bet is probably to add the new Exchange 2003 server as a mailbox server, move mailboxes from the Exchange 2000 server to the Exchange 2003 server, then do an in-place upgrade on the Exchange 2000 server. Once that's done you can change the server role on the former Exchange 2000 box to make it a front-end and you'll be done.

paulrobichaux November 15, 2006 (Article Rating: )


--------------------------------------------------------------------------------

hi
i will use the hard way . but i tried that backing up c drive and the system state together .and it is not working fine with me ..
do you advice me with take a backup without system state ..
i have windows 2003 ent edtion , + exchange 2003 sp1

lorinseribo March 19, 2007 (Article Rating: )
Pour ce faire il faut utiliser « NTDSUTIL »

1.Cliquez sur Démarrer, sur Exécuter, tapez cmd dans la zone Ouvrir, puis appuyez sur ENTRÉE.
2.Tapez ntdsutil et appuyez sur ENTRÉE.
3.Tapez roles et appuyez sur ENTRÉE.
4.Tapez connection et appuyez sur ENTRÉE.
5.Tapez connect to server nom_serveur, où nom_serveur est le nom du contrôleur de domaine où sera assigné ce rôle, puis appuyez sur ENTRÉE.
6.Tapez quit et appuyez sur ENTRÉE.
7.Selon le rôle a transférer, tapez transfer infrastructure master, transfer PDC, transfer RID master, transfer domain naming master ou transfer infrastructure master et appuyez sur ENTRÉE.
voir cet article Microsoft http://www.laboratoire-microsoft.org/articles/win/FSMO/6/
merci à Camille BEFFARA, Mathieu MANSION et Nicolas MILBRAND pour ce document

Serveur DHCP avec SBS 2003

http://www.ybet.be/oper-2003/sbs-dhcp.php


7. Serveur DHCP avec SBS 2003
1. Introduction - 2. Installation - 3. Configuration


1. Introduction.
Un serveur DHCP permet de donner dynamiquement une adresse IP à des ordinateurs. Il peut être intégré dans un routeur ou ... dans une configuration serveur. Si vous démarrez l'installation de SBS 2003 avec deux cartes réseaux intégrées, l'une pour le réseau loval, l'autre pour la connexion Internet, il est installé par défaut sur la partie locale (pas pour la partie internet, utilisant une connexion sur un routeur).

Cette partie permet d'installer le serveur DHCP après l'installation complète du serveur. La partie cliente est d'office installée.

2. Installation.
Le serveur DHCP est un composant additionnel de Windows. Pour l'installer, dans le panneau de configuration, sélectionnez "Ajout / Suppression de Programme". A droite, sélectionnez la commande Ajouts de composants Windows. Le Protocole DHCP se trouve dans la rubrique "Services de mises en réseau".



Ceci n'est que la première partie, le service est bien démarré si vous vérifiez dans la liste des services exécutés, mais il nous reste à le configurer.

La première opération consiste à mettre une adresse IP fixe sur la carte Ethernet connectée au réseau local. C'est obligatoire. La partie suivante va être de configurer la plage d'adresse.

3. Configuration.
Dans les outils d'administration, nous allons directement sélectionner la commande DHCP

La fenêtre va bien nous montrer qu'il est actif, mais aucune plage n'est configurée. Pour débuter cette configuration, dans le menu Action, sélectionnez la commande Nouvelle étendue.



Après avoir entrer une description de cette plage, nous allons configurer le serveur.

La configuration demande l'adresse IP de début et celle de fin. Ces deux adresses doivent obligatoirement se située dans la même plage que l'adresse IP de la carte réseau. Dans notre exercice, elle a été configurée en 192.168.0.1. Nous attribuons comme plage 192.168.0.5 à 192.168.0.100. Les adresses 2 à 4 sont laissées pour éventuellement insérer des équipements fixes comme un routeur ou un switch administrable. Le masque de sous-réseau est proposé automatiquement mais peut-être modifié.



L'étape suivante permet d'exclure des plages d'adresses dans l'étendue créée ci-dessus. Dans notre cas, ce n'est pas nécessaire.

Vient ensuite la durée du bail de l'adresse. Par défaut, elle est de 8 heures mais peut être augmentée (typiquement 72 heures). Cette durée va déterminer le temps où les ordinateurs stations vont conserver l'adresse IP dynamique avant d'en demander une nouvelle.

Reste à configurer les options annexes. Lorsqu'un client reçoit une adresse dynamique, il va utiliser d'autres options que nous allons configurer comme les serveurs DNS et Win.

La première étape est celle du routeur, appelé passerelle dans les configurations réseaux. Si vous utiliser un routeur pour votre connexion Internet directement sur le réseau local, c'est cette adresse qui doit être rentrée. Dans notre cas, en utilisant deux connexions réseaux distinctes, c'est l'adresse IP du serveur qui doit être renseigné, soit 192.168.0.1.

A l'étape suivante, c'est le DNS qui va être configuré. Dans notre cas, entrons le nom du serveur, soit dans notre exemple le serveur est configuré comme contrôleur de domaine principal: YBET-S1. Vous pouvez également mettre le DNS primaire de votre fournisseur d'accès mais ce n'est pas nécessaire puisque le serveur SBS 2003 sert ici de passerelle (toutes les connexions passent par lui) et c'est le serveur DHCP connecté sur l'autre carte (le routeur) qui va donner ces adresses automatiquement.



Reste le serveur WINS utilisé par le protocole NetBios pour compatibilité avec les ordinateurs fonctionnant sous Windows antérieurs à 2000 (en gros NT et Windows 98 avec l'add-on du CD installé). Ce n'est normalement plus nécessaire.

Il ne nous reste plus qu'à activer l'étendue pour terminer la configuration de notre serveur. Ceci nécessite de réinitialiser les carte réseaux des stations dans certains cas. Le plus simple est de désactiver la carte Ethernet dans les connexions réseaux et de la réactiver.

Une fois terminée, la plage d'adresse est maintenant clairement définie sur l'administration, même si vous pouvez modifier les paramètres au cas par cas comme la durée du bail, l'adresse du routeur - passerelle, ...